Sun Enterprise 10000 Server
 

GCS>Sun Microsystems>Servers>High-End Servers
 

You will use the System Service Process (SSP) as a boot server for the domain's new operating system. The SSP is a SPARC[TM] workstation or SPARC server that enables you to control and monitor the Sun Enterprise[TM] 10000 system. You can use a Sun Ultra[TM] 5 or Sun Enterprise[TM] 250 workstation, or a Sun Netra[TM] T1 server as an SSP.

Complete Procedure for Creating a New Domain on a Sun Enterprise[TM] 10000 Platform.
---------------------------------------------------------------------------------------------------------------------------------
As an example, the procedure in this document creates a new domain called "bob" on a platform called "mye10k," using system boards 1 and 12, running the Solaris[TM] 8 Operating System on ip address 192.168.100.1.

Step 1. Inserting the New Hardware
---------------------------------------------------------

1. Select 2 empty slots for the new boards to be inserted into, or select
   present but unused System Boards currently in the platform.
2. The domain must have the following to be able to support an operating
   system.
   • 1 to 4 CPUs on the system board.
   • Memory (The system boards only support fully populated banks of
     32 MB or 128 MB memory. Mixing memory in a board is not supported.)
   • Sbus or PCI mezzanine with at least 1 supported Host Bus Adaptor
     (HBA) for the boot.
   • At least one Sbus or PCI network interface for the net boot from
     the boot server.
3. Insert the new hardware.
4. On the MAIN ssp, Power on the new boards:

         mye10k:bob% power -on -sb 1 12 

Step 2. Running the Autoconfig Command
--------------------------------------------------------------------
CAUTION: Run the autoconfig command only on the new or moved boards. Incorrectly running the autoconfig command could cause running domains to fail.

1. On MAIN SSP as user ssp:
   mye10k:bob% setfailover off
2. Run Autoconfig:
   mye10k:bob% autoconfig sysboard1 (ensure there is no space between sysboard and board #)
   Do not reboot yet
   mye10k:bob% autoconfig sysboard12
   Now reboot the SSP.
   Note: in this case there is no need to sync the SSPs because failover is set to 'off'.
3. When the SSP is back up (confirmed by running showfailover):

           mye10k:bob% setfailover on (this should sync the SSP's)

Step 3. Preparing the SSP Domain Environment
-----------------------------------------------------------------------------

1. Verify that you have a eeprom image for your domain that is NOT
   being used for an existing domain.
2. Log in to MAIN SSP as user ssp.
3. mye10k:bob% cd $SSPVAR/.ssp_private/eeprom_save
4. Select an unused eeprom image if you have one, for example,
   eeprom.image_8:
   mye10k:bob% mv eeprom.image_8 eeprom.image.bob
   NOTE: It is always better to move the unused file to the name of
   the domain rather than coping the file. Moving the unused file
   reduces the chance of the file being reused and causing duplicate
   host ids on your platform. If you do not have a spare image, request
   a new key from Sun Microsystems so that you can create an image.
   To create an image, use the Sun supplied key and serial number with
   the sys_id command.
   To determine if an image is used, you can check it's mac address and
   compare to the current domains.
   I.E.: mye10k:bob% sys_id -d -f eeprom.image_8
   IDPROM in eeprom.image_8
   Format = 0x01
   Machine Type = 0x80
   Ethernet Address = 0:0:be:a6:7f:9a
   Manufacturing Date = Wed Dec 31 19:00:00 1969
   Serial Number (Host ID) = 0xa67f9a
   Checksum = 0x3f
5. Create the new domain:
   mye10k:bob% domain_create -d bob -b 1 12 -o 5.8 -p mye10k
   Answer "Yes" to proceed.

Step 4. Powering on the Domain
----------------------------------------------------

1. First change to the correct domain environment:
   mye10k:joe% domain_switch bob
   NOTE: Failure to change to the correct domain environment could result
   in crashing an existing domain.
2. Power on the boards, if they're not powered on already:
   mye10k:bob% power -on -sb 1 12
   mye10k:bob% bringup -A off (This is the equivalent of autoboot=false.)
   The domain will now post with level 16 diagnostics.
3. Confirm the domain passes a single pass level 16.
4. Because this is all new hardware, re-run the bringup with a level
   127 to fully test the hardware:
   mye10k:bob% bringup -A off -l127
   mye10k:bob% netcon -g (to connect to the domain after Open Boot PROM
   handover)
   <#0>ok

Step 5. Setting Up for Net Boot
-------------------------------------------------

1. It is recommended to use a private network between the SSP and Domains
   to install o/s. Or if the customer has a jumpstart server on the subnet
   allready, point to that.
2. Verify that the network interface you will use is connected to
   the network:
   <#0>ok watch-net-all (to check for traffic)
   <#0>ok show-nets (to get path for nvalias cmd)
3. Identify the interface to which the cable is connected:
   <#0>ok nvalias bootnet <selected interface >
   <#0>ok nvstore
4. Confirm the Mac address (presuming a local_mac_address?=false):
   <#0>ok banner
   Ethernet address 0:0:be:b9:2b:3f (example Mac/ethernet address)
5. As root on the SSP, add bob to /etc/hosts:
   192.168.100.1 bob
6. As root on the SSP, add bob to /etc/ethers:
   0:0:be:b9:2b:3f bob
7. Change directories to the boot image directory:
   root# cd /export/install/8/Solaris_8/Tools
8. Set up bootparams etc:
   root# ./add_install_client bob sun4u
9. On netcon session:
   <#0>ok boot bootnet - install (or the equivalent for the Solaris 9 OS)
10. Answer install questions. For the Solaris 8 OS
    installation, select "no" reboot.
11. root# ls -l /dev/rdsk/c0t0d0s0 (or the disk you installed the new OS on )
    Take note of this path.
12. root# /etc/halt
    <#0>ok show-disks
13. Select the path to disk above:
    <#0>ok nvalias bootdisk <path to disk with new os >
    <#0>ok nvstore
    <#0>ok setenv boot-device=bootdisk bootnet
    <#0>ok setenv diag-device=bootdisk bootnet
    <#0>ok boot bootdisk
    ......
14. Console login: ....
15. Enter the following, which will allow you to correct the host
    name and public ip address, if required:
    root# sys-unconfig
16. root# reboot
17. Boot, configure to the correct addresses, and patch to EIS Standard.
    NOTE: There are specific patches required on an Sun Enterprise 10000 domain above and beyond the standard recommended OS patch bundle. Contact your service representative for a list of these patches or source them from the EIS CD.

• The location of the eeprom keys is at
  
  http://pts-americas.west.sun.com/esg/hsg/starfire/tools/key_display.html
  


• The location of the Sun Enterprise 10000 patches is at
  
  http://pts-americas.west.sun.com/esg/hsg/starfire/patches.html
  

This solution has no attachment