Sun Enterprise 3000 Server
 
Sun Enterprise 4500 Server
 
Sun Enterprise 5500 Server
 
Sun Enterprise 4000 Server
 
Sun Enterprise 5000 Server
 
Sun Enterprise 6000 Server
 
Sun Enterprise 3500 Server
 
Sun Enterprise 6500 Server
 

GCS>Sun Microsystems>Servers>Midrange Servers
 

Description

The document provides instructions, tables, and examples to assist a user in identifying which board slot number is referenced from a Sun Enterprise[TM] (also known as "Ultra Enterprise") 3000, 3500, 4000, 4500, 5000, 5500, 6000, and 6500 Server device path.

Steps to Follow

Example using a device path from an Ultra Enterprise[TM] 3000 Server:

/sbus@3,0/SUNW,fas@3,0/sd@0,0

The first portion ("sbus@3,0")of the device path indicates the I/O board slot location.  In Table 1 below, sbus@3,0 correlates to the I/O board in slot 1 which is located on the rear of the machine (UE 3000's only use the rear, odd number slots because there are internal disks in the front).

I/O Board Sbus@Front/Rear Slot Assignments

Table 1(a): Front Slot Assignments:

Table 1(b): Rear Slot Assignments

The second portion ("SUNW,fas@3,0") of the device path indicates the type of onboard controller and the Sys I/O bus it uses (see Table 2 below).  I/O boards are basically split in half, each half is controlled by a Psycho or Sys I/O chip (A or B).  SUNW,fas@3,0 correlates to the onboard (built-in) fast/wide SCSI controller at Sys I/O B on this board.

Onboard Controller Assignments

Table 2: Onboard Controller Assignments

The next portion of the device path ("sd@0,0") correlates to the SCSI disk (sd) set to target id 0 (in this case an internal disk, since only internal disks should be controlled by the onboard SCSI controller of the I/O board in slot 1).

Example 1:

/sbus@6,0/SUNW,socal@d,0/sf@0,0/ssd@2200002136bcd49,0 (ssd27)

***NOTE: sf@0 is the GBIC port on the right and sf@1 is the GBIC port on the left when looking at an I/O with soc+ (socal) board.; On an Enterprise 3000 & 3500, sf@0 is the GBIC port on the bottom and sf@1 is the GBIC port on the top.

Example 2:

/sbus@5,0/scsi@2,0/st@5,0

Example 3:

Without access to the tables above, one is forced to use a different method to determine slot location.

/sbus@2,0/SUNW,socal@d,10000/sf@0,0/ssd@w21000020370df2a8,0

Divide the "sbus@#" by 2, the remainder is not important.

sbus@2 = Divide the 2 by 2 to reveal the I/O board slot number "2/2 = 1"
I/O board slot number = 1

NOTE:  Always divide the "sbus@#" by 2, the remainder is not important (i.e /sbus@7, 7/2 = 3 r1).

The device drivers used in this example are some of many device drivers that could appear in the device driver section. See examples below:

Note:

From the Ultra™ Enterprise™ 3000 System Installation Guide (802-6050), section 2.7, and the Sun Enterprise 6500/5500/4500 Systems Installation Guide (805-2631) section 2.8:

“External SCSI-2 devices connect to your system through the built-in single-ended Fast/Wide SCSI-2 port on I/O boards (except for the board in slot 1), or through FSBE/S, DSBE/S, SWIS/S, or DWIS/S SBus cards installed on I/O boards.

Note – The onboard SCSI-2 bus on the I/O board in slot 1 controls internal SCSI tray devices. Therefore, the external SCSI connector on the I/O board in slot 1 must always have a terminator installed.”

The HD68, Single Ended, Fast Wide terminator, part number 150-2267, should be used to terminate the SCSI port on I/O board #1.

This solution has no attachment