Sun Fire E25K Server
 
Sun Fire E20K Server
 
Sun Fire 12K Server
 
Sun Fire 15K Server
 

GCS>Sun Microsystems>Sun Alert>Criteria Category>Availability
 
GCS>Sun Microsystems>Sun Alert>Release Phase>Resolved
 

Sun Fire 12K/15K/E20K/E25K systems equipped with UltraSPARC IV or UltraSPARC IV+ System Boards that use high traffic across a Quad GigaSwift (QGE-X) card may panic.

This issue can occur on the following platforms:

• Sun Fire 12K/15K/E20K/25K without patch 118777-13

The described issue only occurs under the following conditions:

1. The Sun Fire 12K/15K/E20K/E25K is equipped with an UltraSPARC IV or UltraSPARC IV+ System Board, and the Quad GigaSwift Ethernet PCIX Card (X4445 - 501-6738)

2. One of the network ports is at or near its peak bandwidth.

3. The network card is running at a frequency over 66MHz.

Note: The more CPU's in a domain, the more likely the panic may occur while the network port is at its peak bandwidth. This issue has not been seen on systems equipped with the UltraSPARC III system boards.

To determine if a system is equipped with a Quad GigaSwift Ethernet PCIX Card (X4445 - 501-6738), the following command can be used:

    # prtdiag
    System Configuration: Sun Microsystems Sun Fire 25000
    System clock frequency: 150 MHz
    Memory size: 327680 Megabytes
   ...
   /IO01/C3V0 PCI 60 A 90 90 1,0 ok pci-pci8086,537c.7/network (netw+ pci-bridge
   /IO01/C3V0 PCI 60 A 90 90 0,0 ok network-pci100b,35.30 SUNW,pci-x-qge
   /IO01/C3V0 PCI 60 A 90 90 1,0 ok network-pci100b,35.30 SUNW,pci-x-qge
   /IO01/C3V0 PCI 60 A 90 90 2,0 ok network-pci100b,35.30 SUNW,pci-x-qge
   /IO01/C3V0 PCI 60 A 90 90 3,0 ok network-pci100b,35.30 SUNW,pci-x-qge
   ...

 Symptoms

If the described issue occurs, a panic string of "Fatal PCI bus error(s)" will be seen.

To work around the described issue, slow down the QGE-X card to use PCI speeds instead of PCIX. This is done by adding a post directive to the "postrc" file on the system controller. The "postrc" file is different for each domain. If there is not a "postrc" file for a specific domain, the platform "postrc" file is used. The domain "postrc" files are located at:

    /etc/opt/SUNWSMS/config/A/.postrc
    /etc/opt/SUNWSMS/config/B/.postrc
   /etc/opt/SUNWSMS/config/C/.postrc
    ...
    /etc/opt/SUNWSMS/config/R/.postrc

The platform "postrc" file is located at:

    /etc/opt/SUNWSMS/config/platform/.postrc

The postrc directive is a single line that is added to this file. The syntax is:

    iobrd_no_pcix exp [ lport [ bus ]]
    iobrd_no_pcix 1 0 0 # changes IOBoard Slot 0 on IO1.

Use this "postrc" directive for every QGE-X card that is in the platform.

Below is an example of the postrc directive and its syntax for each slot:

    iobrd_no_pcix 3 0 0 # changes IOBoard Slot 0 on IO3.
    iobrd_no_pcix 3 1 0 # changes IOBoard Slot 2 on IO3.
    iobrd_no_pcix 3 1 1 # changes IOBoard Slot 3 on IO3.

Note: Slot 1 is not a PCIX slot and is not impacted by this issue.

This issue is adressed in the following release:

• Sun Fire 12K/15K/E20K/E25K with patch 118777-13 or later
  

References

References

This solution has no attachment