| Home | Current Systems | Former STK Products | EOL Systems | Components | General Info | Search | Feedback |
| Sun System Handbook - ISO 3.4 June 2011 Internal/Partner Edition | ||
|
|
||
 |
||||||||||||
Solution Type Problem Resolution Sure Solution 1018741.1 : Sun Cluster[TM] 3.x: SCSI errors after installing SCSI JBOD Disk Array
PreviouslyPublishedAs 230462 Symptoms A new Sun Cluster[TM] 3.x installation used a JBOD unit (in this case, a Sun StorEdge[TM] D2 array in a split mode) for its shared storage. After the installation and testing of the cluster, some problems with the shared array were discovered. The problem occurred when a node was booted into cluster, causing many SCSI warnings and a volume managment problem on the other node. In this case, the metadevices needed maintenance. The errors did not occur if the node was booted outside of the cluster. Symptoms: On the Node Being booted: Dec 4 12:15:04 nodeA pseudo: [ID 129642 kern.info] pseudo-device: tod0 Dec 4 12:15:04 nodeA genunix: [ID 936769 kern.info] tod0 is /pseudo/tod@0 Dec 4 12:15:04 nodeA pseudo: [ID 129642 kern.info] pseudo-device: pm0 Dec 4 12:15:04 nodeA genunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0 Dec 4 12:15:04 nodeA syslogd: going down on signal 15 Dec 4 12:15:04 nodeA xntpd[224]: [ID 866926 daemon.notice] xntpd exiting on signal 15 Dec 4 12:15:26 nodeA genunix: [ID 672855 kern.notice] syncing file systems... Dec 4 12:15:26 nodeA genunix: [ID 904073 kern.notice] done Dec 4 12:16:40 nodeA genunix: [ID 540533 kern.notice] ^MSunOS Release 5.8 Version Generic_108528-16 64-bit Dec 4 12:16:40 nodeA genunix: [ID 913631 kern.notice] Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved. Dec 4 12:16:40 nodeA genunix: [ID 678236 kern.info] Ethernet address = 0:3:ba:17:f8:6e SCSI Errors on NodeB: Dec 4 12:15:34 nodeB eri: [ID 517527 kern.info] SUNW,eri0 : 100 Mbps full duplex link up Dec 4 12:16:10 nodeB scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus2): Dec 4 12:16:10 nodeB Received unexpected SCSI Reset Dec 4 12:16:15 nodeB scsi: [ID 107833 kern.warning] WARNING: /pci@8,700000/pci@2/scsi@4 (qus0): Dec 4 12:16:15 nodeB Received unexpected SCSI Reset Dec 4 12:16:19 nodeB scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4/sd@8,0 (sd82): Dec 4 12:16:19 nodeB Error for Command: write Error Level: Retryable Dec 4 12:16:19 nodeB scsi: [ID 107833 kern.notice] Requested Block: 67 Error Block: 67 Dec 4 12:16:19 nodeB scsi: [ID 107833 kern.notice] Vendor: FUJITSU Serial Number: 0228X67457 Dec 4 12:16:19 nodeB scsi: [ID 107833 kern.notice] Sense Key: Aborted Command Dec 4 12:16:19 nodeB scsi: [ID 107833 kern.notice] ASC: 0x47 (scsi parity error), ASCQ: 0x0, FRU: 0x0 Dec 4 12:16:19 nodeB scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus2): Dec 4 12:16:19 nodeB Target synch. rate reduced. tgt 8 lun 0 Dec 4 12:16:19 nodeB scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4/sd@9,0 (sd83): Dec 4 12:16:19 nodeB Error for Command: write Error Level: Retryable Resolution Steps for Resolution Change the scsi-initiator-id on one node to 6 globally for all devices at the OBP level and then use the nvramrc script to set the scsi-initiator-id to 7 on the local devices. You can find the complete procedure in the Sun Cluster 3.x With
SCSI JBOD Storage Device Manual for Solaris OS under 1.
Installing a SCSI JBOD Storage Device, Installing a Storage
Array, How to Install a Storage Array See bugs: BugID: 4663904 , BugID: 4670376 , BugID: 4669448 Product Sun StorageTek D2 Array Sun Cluster 3.0 Sun Cluster 3.1, Sun Cluster 3.0, D2, array, scsi errors, scsi, jbod, scsi-initiator-id, cluster Previously Published As 49560 Change History Publishing Information Date: 2005-03-07 User Name: 71396 Action: Approved Comment: Performed a final review of the article. Attachments This solution has no attachment |
||||||||||||
|
||||||||||||