Sun Microsystems, Inc.   Sun System Handbook - ISO 3.4 June 2011 Internal/Partner Edition
   Home | Current Systems | Former STK Products | EOL Systems | Components | General Info | Search | Feedback

SPARCprinter

Option SPRN-400
Xerox 4030

PART # DESCRIPTION
365-1089 SPARCprinter (115V & 240V)
365-1124 Toner Cartridge 1
365-1125 Drum Cartridge 2
365-1126 Universal Paper Tray
365-1127 B4 Paper Tray
370-1365 Video Port Cable, Video Port to SPARCprinter
410-1017 Reusable Field Service Transit Case
501-1540 SBus Printer Board
530-1680 Parallel Port Cable
530-1683 Loopback Test Cable, Parallel Port to Video Port
530-1694 Test Cable, Video Port to Video Port
811-1345 Front Cover
811-1316 Corotron Assembly
811-1687 Fuser Wick 94E95090 (available from SunExpress)
  1. The life of the Toner Cartridge is 8000 pages. A J5 error code indicates a low toner condition. Reset the display when a new Toner Cartridge is installed.
    a. Turn the AC power OFF.
    b. Replace the Toner Cartridge.
    c. Turn the AC power ON.
    d. Press the Reset button located next to the power switch.
  2. The life of the Drum Cartridge is 20,000 pages. Reset the print counter when a new Drum Cartridge is installed.
    a. Turn the AC power OFF.
    b. Install a new Drum Cartridge.
    b. Press and hold the Reset button located next to the power switch.
    c. Turn the AC power ON.
    d. Release the Reset button.

Do not reset the print counter unless a new Drum Cartridge is installed. Resetting the print counter without replacing the Drum Cartridge causes mechanical damage to the SPARCprinter when the toner sump fills.

SPARCprinter Operator Panel

SPARCprinter IOT Test Print

  1. Switch the printer OFF.
  2. Press and hold TEST.
  3. Switch the printer ON.
  4. Release TEST. 00 is displayed. The printer must warm-up for approximately one minute in order to print a test page.
  5. Press ENTER to start printing the IOT test print. The display indicates the number of test pages printed.
  6. Press ENTER to stop printing the IOT test print.
  7. Switch the printer OFF to exit the IOT Test Print Mode.

Reference

SPARCprinter Service Guide, 800-5044-10.

SPARCprinter Input Component Tests

  1. Switch the printer OFF.
  2. Press and hold ENTER.
  3. Switch the printer ON.
  4. Release ENTER. The Operator Panel displays 02.
  5. Press ENTER to select the Input Component Tests. The Operator Panel displays 00.
  6. The following input components can be tested: Fuser Exit Sensor, Toner Cartridge Switch, Paper Size Sensors, Drum Cartridge Switch, Paper Tray Empty Sensors, Manual Bypass Feature Switch, Reset Switch, Interlock Switch, and Test Switch. The input component is functional if the value displayed in the Operator Panel increases when the component is activated.
  7. Switch the printer OFF to exit the Sensor Check Diagnostics

SPARCprinter Output Component Tests

  1. Switch the printer OFF.
  2. Press and hold ENTER.
  3. Switch the printer ON.
  4. Press TEST until the desired diagnostic test number is displayed in the Operator Panel. The following output components can be tested:
    Component Test Code
    Print Counter 30
    Upper Feed Clutch 80
    Lower Feed Clutch 81
    Registration Clutch 82
    Upper Turn Roll Clutch 84
    Lower Turn Roll Clutch 84
    Main Motor & Erase Lamp 90
    HVPS 90
  5. Press ENTER to test the component.
  6. Switch the printer OFF to exit the Sensor Check Diagnostics.

SPARCprinter NVRAM Parameters

  1. Switch the printer OFF.
  2. Press and hold TEST and ENTER.
  3. Switch the printer ON.
  4. Release TEST.
  5. Release ENTER when the display shows 03.
  6. The NVRAM parameter and value are displayed.
  7. Press ENTER to change a value.
  8. Press TEST to store a new value.
  9. Press TEST to display the next parameter.
  10. Switch the printer OFF to exit the NVRAM Parameters.
Function Address Content
Processing Direction 0 xx 1
Scanning Direction 1 xx 2
IOT Test Print 2 NA 3
Fuser Temperature 3 xx 4
Laser Power 4 xx 4
Resolution 5 xx 4
Video Mode 6 xx 4
Configuration 7 xx 3
Paper matrix 8 xx 4
Console Type 9 xx 4
  1. Processing Direction controls the top and bottom page margin. Each increment from 0 to F adjusts the margin 0.5 mm.
  2. Scanning Direction controls the left and right page margin. Each increment from 0 to 8 adjusts the margin 0.5 mm.
  3. Press ENTER to print one test page.
  4. Do NOT change these factory settings.

SPARCprinter Error Codes

RAP DESCRIPTION
C3
C5
C9
No paper tray is detected.
The paper tray is empty.
A paper tray print was requested when there is paper in the manual feed tray.
E1
E4
E5
A paper jam at the infeed roller has occurred.
A paper jam at the outfeed roller has occurred.
The top cover is open.
J2
J3
J4
J5
No drum cartridge is detected.
No toner cartridge is detected.
The drum cartridge has reached end of life.
The toner cartridge is empty.
P1 The fuser has shut down
U1
U2
U4
The main motor speed dropped below normal during a print cycle.
Laser Failure
Fuser Failure


Last updated: December 2, 1996
  Copyright � 2011 Sun Microsystems, Inc.  All rights reserved.
 Feedback