Sun Microsystems, Inc.   Sun System Handbook - ISO 3.4 June 2011 Internal/Partner Edition
   Home | Current Systems | Former STK Products | EOL Systems | Components | General Info | Search | Feedback

Seagate ST41600N (1.3GB)

976002-012 Elite-1 Family
5 1/4" 5400 RPM Single Ended SCSI

Sun-4/470 / SS630MP / SS670MP
Option 571

370-1377
3 1/4" Height

Top View

End View

In the Desktop Storage Module, orient Pin-1
of the Address Select Switch Cable with ID2
on J5. Remove all jumpers from J4A.

Power

2.4 Amps @ +5Vdc
2.1 Amps @ +12Vdc
37.2 Watts

Jumper Settings

Jumper J4A Jumper J5 Jumper J4B
J4A
JUMPER SETTING DESCRIPTION
ID0,ID1,ID 2 Out Drive ID select, Target 0
ID0 In Drive ID select, Target 1
ID1 In Drive ID select, Target 2
ID0,ID1 In Drive ID select, Target 3
WRT Out Write enabled
SLV Out Spindle sync master

J5*
JUMPER SETTING DESCRIPTION
ID0,ID1,ID 2 Out Drive ID select, Target 0
ID0 In Drive ID select, Target 1
ID1 In Drive ID select, Target 2
ID0,ID1 In Drive ID select, Target 3
* Factory configurations do not use shunts at Jumper J5.

J4B
JUMPER SETTING DESCRIPTION
SDO In Spinup Delay = 10sec x Target ID
SCO Out Spinup according to SD0 setting
SCP Out Parity enabled
SWP In Sweep cycle enabled

J01
JUMPER SETTING DESCRIPTION
1-2
The drive supplies TERMPWR to its own terminator.
It does not supply TERMPWR to the SCSI bus.
2-4
The drive supplies no TERMPWR.
The initiator supplies TERMPWR to the bus.
1-3
2-4
In
In
The drive supplies TERMPWR for the external
terminator at the end of the daisy chain. This
option is recommended only for the last drive
on a daisy chain.

Notes

  1. The minimum operating system is SunOS 4.1.1.
  2. SunOS 4.1.1 Sun-4c requires the 1.3GB Disk Drive Enhancement (esp.o, sd.o, and format.dat).
  3. SunOS 4.1.1 Rev B Sun-4c requires the 1.3GB Disk Drive Enhancement (esp.o and sd.o).
  4. SunOS 4.1.1 Sun-4 requires the 1.3GB Disk Drive Enhancement (format.dat).
  5. Jumper J4A uses 2 mm shunts. Jumper J5 can be configured using 2.54 mm shunt 130-0272. The Target ID is the Boolean OR of J4A and J5. Do NOT install shunts in both locations. Do NOT install shunts at J4A when the address select switch cable is installed.
  6. The 1.3GB Disk Drive is not supported inside Sun 12-Slot Office Pedestals that use SCSI Interface PCBs 501-1493 and 501-1496.
  7. The 1.3GB Disk Drive is not supported inside SCSI Peripheral Trays that use SCSI Interface PCB 501-1496.

References

  1. Desktop Storage Module Service Manual, 800-6219-10.
  2. Desktop Storage Module Service Manual, 800-7236-10.
  3. Sun SCSI Expansion Pedestal Service Manual, 800-6402-11.
  4. Sun SCSI Expansion Pedestal Service Manual, 800-7285-10.
  5. 12-Slot Office Pedestal with Single Peripheral Tray, 800-6497-10.


Last updated: December 2, 1996
  Copyright � 2011 Sun Microsystems, Inc.  All rights reserved.
 Feedback